Kenmore Refrigerator 795 Ice Maker Problem Troubleshooting!
The Kenmore fridge, model 795, is a champ at churning out ice like nobody’s business. Yet, as time marches on, it might run into a snag or two. But hey, no worries – these hiccups are fixable.
Some common problems include leaking, the ice maker not dispensing or producing ice, or dispensing too little or too much ice.
The ice maker might also dispense ice too slowly, fail to fill up with water, freeze up, or stop suddenly.
Quick Kenmore Refrigerator Model 795 Troubleshooting
Problem | Probable Cause | Quick Fix |
1. Ice Making Leaking | – Malfunctioning fill valve | – Replace the fill tube |
– Frosted fill tube | – Unfreeze the fill tube by running hot water through it | |
– Low water pressure | – Adjust the water pressure or fit a low-pressure valve | |
– Drain clogging | – Clean the condensation drains | |
– Ice jam | – Remove the ice mass | |
– Expired filter | – Replace the expired filter | |
2. Slow Ice Maker | – High temperature | – Reduce the temperature to 12°F |
– Faulty water filter | – Replace the filter | |
– Blocked water line | – Remove the source of blocking | |
– Overstocking or understocking | – Don’t overstock or understock your unit | |
3. Ice Maker is Not Making Ice | – Frozen line/evaporator coil | – Unclog the waterline and condenser coil |
– Clogged water filter | – Replace the water filter | |
– Faulty water inlet valve | – Replace faulty inlet valve | |
– Incorrect temperature | – Readjust the temperature to 12°F | |
– Defective thermostat | – Replace the thermostat | |
– Failing ice maker | – Kenmore Elite 795 ice maker replacement | |
4. Kenmore Ice Maker Freezing Up | – Inadequate water supply | – Improve water supply |
– The fridge door doesn’t shut well | – Fix the door to ensure it shuts completely | |
5. Kenmore Ice Maker Not Dispensing Ice | – Ice clog | – Remove the ice clog |
– Faulty actuator | – Replace the actuator | |
– Faulty motor | – Replace the motor | |
– Faulty control board | – Replace the control board | |
– Dirty condenser | – Clean the condenser | |
– Defective door switch | – Replace the bad door switch | |
– Faulty heating element | – Replace the heating element | |
6. Ice Maker Dispensing Little Ice | – Incorrect temperature | – Adjust the unit’s temperature |
– Faulty water filter | – Replace the faulty filter | |
– Frozen or clogged drain | – Unclog the water line | |
– Out-of-level fridge | – Level the Kenmore unit | |
7. Ice Maker Dispensing Too Much Ice | – Wrong ice bin position | – Reposition the ice bin properly |
– Problem feeler arm | – Replace the broken feeler arm | |
– Low pressure | – Adjust the water pressure | |
– Defective water inlet valve | – Replace defective water valve | |
8. Kenmore Ice Maker Not Filling With Water | – Clogged drain | – Unclog the drain |
– Faulty water inlet valve | – Test the continuity of the valve and replace it if faulty | |
9. Ice Maker Suddenly Stops | – Ice obstruction on the ejector’s arm | – Remove ice obstruction on the ejector’s arm |
Diagnosing and Fixing Ice Maker Problems in Your Kenmore Refrigerator 795
If you’re experiencing issues with the ice maker in your Kenmore refrigerator 795, there are several common problems you can diagnose and potentially fix at home. Here are nine common ice maker problems and their solutions:
Kenmore Elite 795 Ice Maker Leaking
If your Kenmore ice maker is leaking, it can be frustrating. Here are potential causes and their fixes:
- Malfunctioning Fill Tube: Replace the fill tube if it’s faulty and causing water to leak into the freezer instead of filling the ice maker.
- Frosted Fill Tube: Thaw the fill tube by running hot water through it or defrosting the unit to prevent water leakage.
- Drain Clogging: Clean the condensation drains located at the base of the freezer to prevent water from leaking into the freezer.
- Expired Filter: Replace the water filter if it’s expired and causing water leakage.
- Ice Jam: Unplug the unit and remove any ice jams to prevent water from leaking into the ice bin.
- Low Water Pressure: Adjust the water pressure or replace the valve to ensure it’s at least 20 psi.
Slow Kenmore Refrigerator 795 Ice Maker
If your ice maker is producing ice slowly, consider the following factors:
- High Temperature: Adjust the freezer temperature to 12°F to encourage faster ice production.
- Faulty Water Line: Clear any ice or debris clogs from the water line to ensure proper water flow.
- Blocked Water Filter: Replace a clogged water filter to improve water supply to the ice maker.
- Overstocking or Understocking: Avoid overloading or underloading the refrigerator, as it can affect ice production.
Kenmore Refrigerator 795 Ice Maker Not Making Ice
If your ice maker is not making any ice, investigate the following potential causes:
- Frozen Line or Evaporator Coil: Thaw and unclog the waterline and evaporator coil if ice is blocking them.
- Clogged Water Filter: Replace a clogged water filter to ensure proper water flow and ice production.
- Faulty Water Inlet Valve: Test the water inlet valve with a multimeter and replace it if it’s defective.
- Incorrect Temperature Setting: Adjust the ice maker temperature to around 12°F for optimal ice production.
- Defective Thermostat: Replace a faulty thermostat that is unresponsive and preventing ice production.
- Failing Ice Maker: If the ice maker is old or severely damaged, consider replacing it entirely.
Kenmore Refrigerator 795 Ice Maker Freezing Up
If your ice maker is freezing up, consider these potential causes:
- Inadequate Water Supply: Improve water supply to the ice tray to prevent ice from overfilling and freezing.
- Door Not Shutting Well: Ensure the freezer door closes properly to prevent warm air from entering and causing ice to thaw and refreeze.
Ice Maker Not Dispensing Ice
If your ice maker is not dispensing ice, consider the following factors:
- Ice Clog: Remove any ice clumps around the ice bin and dispenser to clear the clog.
- Faulty Actuator: Replace a faulty actuator that is not properly sending signals to the ice maker.
- Faulty Control Board: If the control board is defective, it may need to be replaced by a professional.
- Defective Door Switch: Test the door switch for continuity using a multimeter and replace it if necessary.
- Faulty Motor: Test the motor for continuity using a multimeter and replace it if there is no continuity.
Insufficient Ice Dispensing
If your ice maker is only producing small or hollow ice cubes, consider the following possible causes and solutions:
- Incorrect Temperature: Check the temperature of the unit using a fridge thermometer and adjust it accordingly.
- Faulty Water Filter: Replace the clogged or worn-out water filter to ensure proper water flow to the ice maker.
- Frozen or Clogged Drain: Inspect the waterline for any kinks or clogs and clear them to restore water supply and ice dispensing.
- Refrigerator Not Level: Reposition the Kenmore refrigerator to ensure it is level, as an uneven position can affect ice production and dispensing.
Excessive Ice Dispensing
On the other hand, if your ice maker is dispensing an excessive amount of ice, consider the following reasons and solutions:
- Incorrect Ice Bin Position: Check that the ice bin is correctly positioned to prevent overflow.
- Broken Feeler Arm: If the feeler arm is broken, it won’t sense a filled ice bucket, leading to overflow. Seek assistance from an expert to replace the broken arm.
- Low Water Pressure: Adjust the water pressure to around 20 psi using a water pressure gauge to ensure the inlet valve closes properly.
- Defective Water Inlet Valve: Test the water inlet valve with a multimeter and replace it if it is faulty, as a defective valve can result in continuous water flow and overflowing ice.
Ice Maker Not Filling with Water:
If your ice maker is not filling up with water, consider the following reasons and solutions:
- Clogged Drain/Filter: Replace the filter if it is clogged with dirt and clean the drain to ensure proper water flow.
- Faulty Water Inlet Valve: Test the water inlet valve for continuity using a multimeter. If there is no continuity, replace the valve.
- Out-of-Position Control Arm: Reposition the control arm near the ice bucket and ensure it is in the down position.
- Unit Needs Resetting: Reset your ice maker by pressing the reset button, restarting the refrigerator, or adjusting the feeler arm after a major repair.
- Ice Maker Switched Off: Ensure that the ice maker is plugged in and switched on.
Ice Maker Suddenly Stops Working
If your Kenmore ice maker suddenly stops working despite previously functioning correctly, there may be ice obstructing the ejector arm.
Fix the problem by removing the obstruction that is preventing the ice maker from operating properly.
Conclusion
If your Kenmore Refrigerator 795 ice maker is not functioning as expected, refer to this troubleshooting guide to identify and resolve the issue.
By following these steps, you can diagnose the problem and take appropriate measures to fix your Kenmore ice maker.