A Kenmore Elite refrigerator can be one of the best purchase decisions for your kitchen. However, what do you do when it malfunctions and requires resetting?
Before you begin panicking, understand that troubleshooting your Kenmore refrigerator isn’t a herculean task. In fact, you can learn how to reset a Kenmore refrigerator easily at home in a few simple steps.
And this guide will tell you the step-by-step process of resetting the fridge and explain the necessary details about the different parts. So, let’s begin!
How To Reset A Kenmore Refrigerator?
Unlike the other appliances that you have at home, a Kenmore Elite refrigerator does not have a dedicated reset switch that you can use. So, if you are wondering, “how can I reset my Kenmore fridge without a reset button and bring it back to normal operation?” don’t worry.
Here are the simple steps you need to follow to reset most Kenmore refrigerators.
Step 1: Begin by opening the refrigerator door and locating the “home” and “ultra ice” buttons. Once you locate them, press and hold the buttons at the same time for three to five seconds. This should switch off the fridge and freezer controls.
Step 2: Now, locate the refrigerator power cord, which is usually behind the unit. Unplug the refrigerator’s power by pulling the plug gently from its wall outlet. This will completely disconnect electrical power from the fridge.
Step 3: Wait for a few seconds, then place the refrigerator’s power cord back into the power outlet to restore power. Once the fridge turns back on, it should reset and resume normal operation.
How To Troubleshoot Resetting The Display On Your Kenmore Refrigerator
Sometimes, you may notice that the display on a Kenmore fridge may not be functioning correctly. In this case, you have to conduct a master reset and troubleshoot to resolve the issue. And here are the simple steps to do that:
Step 1: On your Kenmore Elite refrigerator, locate the refrigerator breaker in the service panel.
Step 2: For this step, you can either unplug the refrigerator’s power cord or choose to turn off the refrigerator breaker.
Step 3: Now, restore the power by putting it back into the power outlet and observe the display panel. It should ideally be reset.
Why Is Your Kenmore Freezer Not Getting Cold?
After successfully completing the resetting process and troubleshooting the fridge, you may notice that the refrigerator freezer or the entire refrigerator compartment is still not getting cold. And there may be a number of reasons for that.
1. Dirty Condenser Coils
One of the most common reasons for poor cooling in Kenmore fridges is dirty condenser coils. Not many people are aware that dirty or chocked condenser coils affect the temperature of the fridge.
The first thing you can do is check if there is anything blocking the condenser fan. Begin by turning off the power button and completely unplugging the refrigerator from the wall outlet. Then, restore power by carefully plugging the outlet cord back into the wall outlet.
At this stage, you should be able to hear or see the condenser fan spinning as the compressor starts running. If not, it is best to call a professional for servicing. You can also attempt removing the blockages on the fans or condenser coils using a blower.
Next, unplug the refrigerator, then check if the condenser coils are dirty. You may have to clean them in order to allow your fridge to produce cold air optimally. Remember that the evaporator fan motor circulates cold air throughout the refrigerator compartments.
If there is only one evaporator fan, it is probably located on the freezer side, so be sure to check it properly before cleaning or replacing it.
2. The Doors Are Not Shut Properly
Another reason your refrigerator compartment may not be cooling properly is because of the doors. It is vital that you shut the refrigerator doors properly every time you open them. Plus, keeping the doors open for too long can cause cold air to seep out of the fridge and affect its cooling capacity.
It is best to keep the doors of the fridge tightly shut and check the sealing. Where you place the fridge can also play a crucial role in its cooling capacity. So, ensure that you don’t place it in an area where it receives sunlight or near any other heating source.
3. The Temperature Settings Are Not Correct
Often, homeowners tamper with the refrigerator’s controls and place it at the coldest setting, thinking it will keep their fridge cooler. However, this can actually affect the cooling capacity of your fridge and cause it to consume more power.
If you have recently purchased a Kenmore refrigerator, you can change the fridge and freezer controls to the lowest setting, so the insides cool faster. And once it reaches a stable temperature, turn it back to your desired setting for optimal cooling.
How Can You Reset The Refrigerator Compressor?
Are you wondering, “how can I reset my Kenmore refrigerator compressor”? Read on to find out.
Step 1: Look for the power cord behind the refrigerator. Once you locate it, gently disconnect it from its wall outlet.
Step 2: Once you unplug the refrigerator to completely disconnect all power sources, look for the ‘0’ or ‘off’ button on the control panel inside the fridge. Then locate the fridge and freezer controls and adjust them to your desired setting.
Step 3: Now, all you do is wait for the fridge to reach a stable temperature. Keep in mind that this could take up to a couple of hours or vene a day to.
How Can You Reset The Control Panel?
Resetting the control panel of a Kenmore fridge is very simple. You can choose to unplug the refrigerator’s power or switch off the refrigerator breaker. Then, plug it back into the wall socket and turn the breaker power on. This will completely reset the control panel.
How To Reset The Defrost Timer?
Do you want to reset the defrost timer on the Kenmore ice maker? Then locate the ‘off’ button on the ice maker to turn off the temperature control. This should be located near the up and down arrows of the ice maker.
Press and hold the ‘off’ button to turn the machine off. Then, plug it back into the socket and wait for about eight seconds for the Kenmore refrigerator ice maker to reset completely.
How To Reset The Electronic Control Board?
Disconnect the refrigerator from its electrical source for about five minutes. Once you plug it back into the power source, the control board should reset automatically.
How To Reset The Water Filter?
There are a couple of steps you need to follow carefully to reset the water filter on your Kenmore. Here are the steps –
Step 1: Locate the control lock and light pads on the fridge and press and hold them for about four seconds.
Step 2: You will notice the water filter indicator light flashing. This is when you let go of both the buttons.
Step 3: Similarly, look for the reset button on the water filter and hold it down for about three to five seconds.
Step 4: Look for the lock and light buttons and press and hold them till you see the indicator lights blinking. Now, find the light button and press it five times within ten seconds. This should reset the water filter. If not, press down on the filter button for five to ten seconds to reset it.
How To Reset A Kenmore After A Power Glitch
In case there is some technical issue with the electrical lines of your home, or you experience a power outage, it is necessary to reset the Kenmore fridge. You will find an up arrow and down arrow on the control board, which you need to press and hold for a few seconds. Once you see ten digits on the display of the control board, let go of the buttons.
Then, click on the alarm reset button and disable the control lock to completely reset the fridge.
There you have it! We hope this helps you understand the different ways to reset Kenmore refrigerators. Although there is no dedicated reset button on them, these simple steps should help you reset any part of the fridge without hassle.
That said, if you notice persisting issues with the service panel or other parts like the ice maker or evaporator fan motor, we recommend calling in a professional. Some issues require expert assistance and services, and it is best left to the professionals.
Until next time!