How To Reset A Frigidaire Refrigerator

Don’t know what to do with a beeping Frigidaire Refrigerator?

It can get overwhelming when your fridge starts beeping or stops abruptly. But more often than not, a simple reset can fix the problem.

However, the fact that this kitchen appliance has several components cannot be ignored. And it is easier to reset a specific part instead of doing a full factory reset.

The bigger question is – how to find the faulty part and tackle it? So, if you are clueless about how to reset a Frigidaire refrigerator, our guide will help you. 

Want to know more? Keep on reading then!

When Should You Reset A Frigidaire Refrigerator?

You can hit the reset button of a Frigidaire refrigerator whenever it stops cooling properly. A few obvious signs of that are:

  • The refrigerator freezer may over frost
  • Fruits and vegetables might rot
  • Poor cooling in the refrigerator compartment
  • Freezer and fridge temps will be high
  • The ice maker won’t function well
  • You won’t be able to feel cold air inside the fridge

How To Reset A Frigidaire Refrigerator?

Frigidaire refrigerators are on top of innovation and technology and have several primary and secondary functioning components. They can start beeping on experiencing obstructions, so you’ll have to reset the fridge to rectify the issue. You can either restore it to factory default settings or focus on a specific troublesome part.

For the latter, you’ll have to inspect the appliance and pinpoint the malfunctioned component. A faulty compressor disrupts the flow of cold air, but the condenser coils might be responsible for a non-functional ice maker. 

But in case multiple parts start giving you a rough time, it calls for a total factory reset. To simplify things for you, we’ll now discuss the different parts of a Frigidaire Refrigerator and how to reset them.

Different Parts Of A Frigidaire Refrigerator

Some of the components of a Frigidaire refrigerator that commonly malfunction or need to be reset are:

  • Alarm system (for power failure, ajar door, high temp, etc.)
  • Air and water filters
  • Compressor
  • Refrigerator display panel
  • Defrost timer
  • Ice dispenser

How To Reset A Frigidaire Refrigerator Control Panel?

The electronic control panel is an integral part of any refrigerator and at times needs a reset when the device heats up too much. For doing this, press the Power Freeze and Power Cool buttons simultaneously on the panel. Keep holding them for a few seconds, and the fridge will reset and start functioning again. 

How To Reset The Frigidaire Refrigerator Alarm?

You might need to reset the  Frigidaire refrigerator alarm after a power outage, which is an easy task. All you need to do is press the “default settings” or “mute” button. In case these buttons aren’t available on your device, select the “options” menu and push “set” to silence the alarm. 

Moving on, to reset the “high temp” alert, press the temp button for a few seconds. After this, the alarm will still beep at certain intervals till it reaches a stable temperature. 

It is usually activated when the refrigerator and freezer cabinets are at 55 degrees and 26 degrees Fahrenheit, respectively, to indicate “too high” temperature. So, ensure that you don’t leave the fridge door open for more than five minutes.

Speaking of which, the “door switch” alarm can be turned off simply by closing the refrigerator door. Just remember to press the “set” button after that. 

How To Reset The Frigidaire Refrigerator Water Filter?

After inspection, if you feel that the filter is creating some trouble, it can be reset in a few simple steps. First off, press the face or end of the filter to unlock and remove it from the compartment. 

Look for obstructions, clean them or replace the filter with a new one altogether; you’ll have to be the judge. Push the replacement into the filter compartment till it clicks, and test it by running the water for two to three minutes

How To Reset The Frigidaire Refrigerator Air Filter?

Resetting the air filter is pretty easy and can be done by pulling out the air filter holder and replacing it with a new one. In case a replacement isn’t required, simply press the “air filter restart” button present on the control panel, and hold it until the display prompts “good.” However, you’ll also need to do it after changing the filter. 

How To Reset The Refrigerator Compressor?

The compressor is the component that circulates cool air in the refrigerator, so if it is down, the whole fridge, along with the eatables, will be affected. Hence, it is important to reset it as soon as possible, and you can do it in three ways:

  • Defrost the fridge manually, or wait for about half an hour if the cycle has started automatically – after that, the compressor will reset. 
  • Set the freezer and refrigerator cabinets in an ideal temperature range in case they were “off.”
  • Remove the power cord, wait for a couple of minutes and plug the refrigerator again.

Most probably, these methods will rest the compressor and get it running smoothly, eliminating warm air from the fridge.

How To Reset The Refrigerator Defrost Timer?

The defrost system ensures that the ice maker of the Frigidaire refrigerator doesn’t generate unwanted frost due to temperature changes or leakages. If your appliance has been frosting a lot lately, you should reset the timer. 

First off, locate the timer panel at the backside or bottom of the device and unscrew it. There will be a projection on the defrost timer’s face, and you’ll need to turn it counter-clockwise. Once that is done, the fridge will automatically shut down in a minute. To confirm, listen to the exhaust fan, as it turns off when the timer is rebooting.

Then, replace the timer panel and wait for 20 to 30 minutes for your fridge to start operating. 

How To Reset A Frigidaire Refrigerator To Factory Setting?

Resetting a Frigidaire refrigerator to factory settings is simple, but note that it will erase your desired cooler setting and other customized refrigerator settings like temperature, alarm tones, etc. If you still want to proceed, then push the “default settings” on the control panel, and you’ll be done. However, it may take up to one day to function properly, so we suggest being patient. 

How To Reset the Code On A Frigidaire Refrigerator?

In case the freezer is displaying an “H1” side panel, it indicates that the temperature is higher than 26 degrees Fahrenheit. And if the same happens on the refrigerator side, it might be above 55 degrees. To reset this code, switch off the appliance, unplug the refrigerator power cord from the wall outlet, and plug it back in after a few minutes. 

Final Words

Having discussed almost all the common parts of a Frigidaire refrigerator, we’ve reached the end of our guide. 

We suggest that instead of rushing to a professional, try resetting your appliance when it starts glitching. There’s a good chance that it will get the fridge running right away or may take up to one day.

However, if a reset doesn’t seem to be helping, then do call for appropriate help. Small issues like alarm beeping or troubles with the light on-off can be neglected, but something like a dysfunctional ice dispenser or a faulty temperature display needs attention. 

Refrigerator’s controls can be tricky to understand, but once you get a hang of it, you’ll be good. That said, we’ll sign off for the day. Until next time, take care!

Similar Posts